 |
www.shoerepairer.info
Welcome to the site for information & support to the shoe repair trade.
The “Voice” of the industry.
Email: admin@shoerepairer.info Phone: +44(0)1502 561333 Text/Mobile: 07866 271271 Office: 18 Snape Drive, Lowestoft, Suffolk, NR32 4SF, UK |
|
|
|
Last Shout - Posted by: stutheshoe - Wednesday, 08 September 2010 14:33
|
|
|
| |
 by Flash » Sun Feb 07, 2010 3:33 pm
Does anyone know how many different Ford Tibbe key cutting codes there are?
-
Flash
- 5+ Poster: New user
-
- Posts: 36
- Joined: Fri Dec 19, 2008 9:36 pm
-
-
TeL200
- 1000+ Poster: Expert user
-
- Posts: 1532
- Joined: Wed Feb 01, 2006 8:13 pm
- Location: Worcester UK
-
by locksnstuff » Sun Feb 07, 2010 10:01 pm
6 cuts on the Tibbe 4 possible depths (1, 2, 3, 4) but 1 of the cuts always has to no. 4 So 4x4x4x4x1
therefore I make is 1024 possibilities, but I do stand to be corrected.
-
locksnstuff
- 5+ Poster: New user
-
- Posts: 13
- Joined: Fri Jul 04, 2008 1:44 am
-
by planet uk900 » Sun Feb 07, 2010 10:33 pm
why would you need to know !!
Trade Engraving Service, Speedy & competitive
Most Brass/Laminate/Corian Plaques despatched to you within 24 hours of your order. Tel: 07971 567 948
-
planet uk900
- Moderator
-
- Posts: 3545
- Joined: Wed Jun 28, 2006 7:26 pm
- Location: Planet Krypton
by grahamparker » Mon Feb 08, 2010 10:31 am
Tel has already given the correct answer.
"You're damned if you do and you're damned if you don't" - Bart Simpson
-
grahamparker
- 50+ Poster: Established user
-
- Posts: 186
- Joined: Fri Jun 26, 2009 8:47 am
- Location: Grimsby
-
by ponsaloti » Mon Feb 08, 2010 4:22 pm
Not done the maths so I dont know how these figures were got and I'm not saying there wrong but, Your never going to get 111114 or 4444441 or much like it in between.
-
ponsaloti
- 50+ Poster: Established user
-
- Posts: 156
- Joined: Mon May 07, 2007 4:16 pm
- Location: uk
-
TeL200
- 1000+ Poster: Expert user
-
- Posts: 1532
- Joined: Wed Feb 01, 2006 8:13 pm
- Location: Worcester UK
-
by Flash » Mon Feb 08, 2010 8:53 pm
Many thanks for the replies.
I didn't need the answer to the question, it was to settle a debate we had about the possible number of cutting codes and if there was a way of calculating the number.
(Granddaughters A level maths)
-
Flash
- 5+ Poster: New user
-
- Posts: 36
- Joined: Fri Dec 19, 2008 9:36 pm
-
by grahamparker » Tue Feb 09, 2010 11:28 am
In reply to lee's question how do you know,
If i look at my silca skp software it lists available codes as 1 to 2330 and this infomation
is supplied to silca by the lock manufacturers so should be correct.
"You're damned if you do and you're damned if you don't" - Bart Simpson
-
grahamparker
- 50+ Poster: Established user
-
- Posts: 186
- Joined: Fri Jun 26, 2009 8:47 am
- Location: Grimsby
-
by planet uk900 » Tue Feb 09, 2010 1:41 pm
Some folk store Geek info....lolalot
Trade Engraving Service, Speedy & competitive
Most Brass/Laminate/Corian Plaques despatched to you within 24 hours of your order. Tel: 07971 567 948
-
planet uk900
- Moderator
-
- Posts: 3545
- Joined: Wed Jun 28, 2006 7:26 pm
- Location: Planet Krypton
Return to Key Cutting - Sponsored by the Charles Birch group.
Who is online
Users browsing this forum: Yahoo and 2 guests
|
|
|
MKPortal ©2003-2008 mkportal.it
|
